Програмирование
Operating modes
At the Comfort motion detector top, three different operating modes can be set by means of a switch:
- Continuous OFF
For this mode, the switch must be moved to the position (1). The lighting is continuously switched off. Switching is not possible by means of extension units.
- Automatic mode
For this mode, the switch must be moved to the position (2). If a motion is detected, the Comfort motion detector top switches on in dependence of brightness and if the motion is no longer detected, it is switched off after the set overrun time has expired. Switching is possible by means of extension units.
- Continuous ON
For this mode, the switch must be moved to the position (3). The lighting is continuously switched on. Switching is not possible by means of extension units.
Interlocking of the switch
By means of an interlocking clip, the switch can be interlocked in the automatic mode of operation switching position:
- Setting the automatic mode of operation
- Carefully remove the slider (1) with a screwdriver.
- Inserting the interlocking clip
Adjusting the overrun time
The overrun time determines how long the lighting remains switched on if a motion is no longer detected. The overrun time can be set within a range of 10 sec to approx. 30 min. The setting is carried out non-linearly, longer times can only be specified within a relatively rough grid.
To modify the overrun time, turn the controller (1) in the desired direction.
If the Comfort motion detector top has switched on, each further detected motion results in a retriggering of the overrun time. This means, the overrun time starts anew.
The Comfort motion detector top does not provide for a forcibly actuated shutdown. This means, continuous motion within the sensing field results in continuous light.
Setting of short-time operation
Within the scope of a special operating mode, the Comfort motion detector top can also be set to short-time duty. The short-time duty operates independent of brightness and can be used, e.g. for controlling a bell.
For this mode the overrun time controller (1) is set to the shortest time (symbol similar to O).
If a motion is detected, the Comfort motion detector top switches on for 0.5 sec. If the detector continues to detect motions, the lighting is not switched on again until an interlocking time of 3 sec has expired.
Setting of the brightness threshold
The brightness threshold is the threshold of the brightness at which a detected movement releases a switching operation. The brightness threshold can be set within a range of approx. 0 to 80 lux.
To modify the brightness threshold, the controller (2) must be turned in the desired direction.
If the controller (2) is set to the "sun" limit stop (> 80 lux), the Comfort motion detector top works in daytime operation and therefore switches independently of brightness.
Note: if the Comfort motion detector top no longer responds to a detected motion at the limit stop "moon" (night setting, 0 lux), the controller (2) must be slightly turned into the sun direction.
The Comfort motion detector top is characterized by a high level of external light immunity. For this reason, the Comfort motion detector top
- does not interpret a short-time illumination, e.g. by means of a flashlight, as brightness threshold exceeded and therefore does not switch on in case of motions. Thus, it is not possible to prevent the motion detector from switching on by illuminating it shortly,
- does not interpret the unintended short-time shadowing, e.g. by a person, as "brightness threshold undergone" and does not switch on in case of motions.
The external light immunity is attained by a time delay.
When brightness turns into darkness, the set brightness threshold must be undergone by at least 10 sec, before detected motions initiate a switching operation.
The same applies to the changeover from darkness to brightness. Only if the set threshold value has been exceeded by at least 10 sec, detected motions no longer initiate a switching operation.
Exception: If the Comfort motion detector top has just switched off, the 10 sec time delay is no longer active.
Releasing the teach function
By means of the teach function, the current ambient brightness can be stored as brightness threshold whereas the brightness threshold set at the controller is no longer evaluated.
To activate the teach function, the Comfort motion detector top must be completely covered within 9 seconds for a short time (approx. 1 sec) at least 3 times, e.g. using the hand.
As soon as the Comfort motion detector top has detected three light changes, the teach function is activated. For acknowledgment,
- The switched on lighting is switched off and subsequently switched on for 3 sec.
- The switched off lighting is switched on for 3 sec.
During the next minute you have to step back from the Comfort motion detector top to ensure that it is able to correctly measure and store the current brightness.
To acknowledge the storage, the lighting is switched on for 3 sec.
Then, the Comfort motion detector top switches into the operating mode set.
If the brightness threshold set at the controller is to be reactivated, the Comfort motion detector top must be pulled off the insert and plugged on again.
Setting the sensitivity
The Comfort motion detector top has an internal algorithm which carries out an automatic adjustment to the ambient conditions. This way, unintended switching operations are nearly eliminated.
Under normal circumstances, the controller should be set to maximum sensitivity.
If, in exceptional cases, it is necessary to determine a different sensitivity level, this can be done using the controller (3). |