Frequency converters SIMOVERT MASTERDRIVES
Motion Control
Documentation and training
Demonstration cases
1-axis system
Stand-alone case equipped with
- Converter
- CBP/CBP2 communications board (for communicating with the PROFIBUS DP demonstration case)
- Control panel
- Pulse resistor
- Radio-interference suppression filter
- Motor, including resolver
- CEE plug for power supply connection, 3-ph. 400 V AC
- DriveMonitor visualization program for PCs.
Dimensions (W x H x D): 360 mm x 500 mm x 235 mm
Weight: approx. 20 kg
2-axis system
Stand-alone case equipped with
- Converter/inverter
- CPB/CBP2 communication board (for communication with the “PROFIBUS DP" demonstration case and the “SIMATIC S7 Motion Control” demonstration case)
- Control panel
- Pulse resistor
- Radio-interference suppression filter
- 1FT6 and 1FK6 servomotors with actual-value encoders
- CEE plug for power supply connection, 3-ph. 400 V AC
- DriveMonitor visualization program for PCs.
Dimensions (W x H x D): 510 mm x 610 mm x 300 mm
Weight: approx. 47 kg
Adapter box for SIMOVERT MASTERDRIVES Motion Control demonstration case
Contains
- Power supply plug, 1-ph. 230 V AC
- CEE socket for demonstration case
- 24 V power supply unit with terminal for the MC converter/inverter.
Dimensions (W x H x D): 230 mm x 170 mm x 170 mm
Weight: approx. 3 kg.
Demonstration case for MASTERDRIVES Motion Control with Drive ES and touch panel
This demonstration case enables the functions of MASTERDRIVES Motor Control units to be demonstrated with a synchronous PROFIBUS DP. The operator uses the TP27 touch panel. A user interface for the TP27 is also supplied to provide the drives of a connected 1-axis or 2-axis demonstration case with setpoints and parameters or to read out faults. A PC/PG with STEP7/Drive ES can be connected to the demonstration case in order to demonstrate the functions of Drive ES.
Hardware structure:
- SIMATIC CPU 316-2DP (direct slave-to-slave traffic, clock synchronicity, routing)
- Power supply
- SIMATIC simulator module
- TP27 touch panel
- TS adapter
- Connecting leads for 1-axis or 2-axis Motion Control demonstration case, and PG/PC with Drive ES.
- Operating instructions for the software supplied for the TP27 for operating a connected 1-axis or 2-axis case.
- Documentation in German/English.
Dimensions (W x H x D): 500 mm x 300 mm x 150 mm
Weight: approx. 8.5 kg
PROFIBUS DP/SIMATIC S7 demonstration case
Enables demonstration of the drives within an automation system.
The PROFIBUS DP demonstration case consists of
- SIMATIC S7-300 (CPU 315-2DP, CP 340 with RS485 interface and 5 A power-supply unit)
- CP340 with RS485 interface for USS protocol (in preparation)
- OP7 operator-control unit
- EPROM with operator-control and control program for PROFIBUS DP
- 3 m PROFIBUS DP cable for two bus stations
- 3 m power-supply cable for connecting 3-ph. 400 V AC
- Two 3-ph. AC CEE sockets (16 A) for connecting SIMOVERT MASTERDRIVES or SIMOREG K 6RA24 demonstration cases
- Two 1-ph. 230 V AC sockets.
The documentation describes the hardware, the STEP 7 program and how to use the demonstration case.
Dimensions (W x H x D): 550 mm x 410 mm x 350 mm
Weight: approx. 20 kg
Transport trolley for demonstration units, suitable for 1-axis and 2-axis demonstration case
Sturdy transport trolley for demonstration case consisting of an aluminium frame with a telescopic handle and wheels with roller bearings. The transport trolley is fitted with an elastic strap for holding the demonstration case in place during transport. The trolley can be folded up for storage.
Dimensions when folded up:
Height folded/open: approx. 662/1020 mm
Width: approx. 480 mm
Weight: approx. 5 kg.
| 
